KNOWLEDGES

Home|KNOWLEDGES
12 06, 2020

All CAT40 End Mill Tool Holder Side Lock Tool Holder

2020-08-25T04:43:38+00:00June 12th, 2020|Categories: Catalogue|

CAT40 end mill tool holder CAT40  side lock tool holder 1/8 ,3/16,1/4,3/8,1/2,5/8,3/4,1",1-1/4",1-1/2 " available Gage length from 1.75" to 6" side lock screw has  1 or 2  , it depends on one how big the hole and what gage length all hole and taper by CNC grinding machine, taper has three times grinding The end

12 06, 2020

Promotion CAT40 ER Collet Chuck Tool Holder Stock in USA

2020-06-12T00:17:55+00:00June 12th, 2020|Categories: Catalogue|

Promotion CAT40 ER Collet Chuck Tool Holder Stock in USA High Precision ER Collet Chuck tool Hoder High-Performance G2.5 25000rpm High precision  TIR: 0.005mm/0.0002" Silver coated never rusty ever   CAT40 ER40 ,ER32,ER25,ER20 ER16 and ER11 Gage length 0.5" to 6" available   NO  Type CAT Tool Holder 1 ER ColletChuck CAT40 5/8-11 CAT40 ER16

14 11, 2019

Precision ER Collets Range ER8 To ER50 Run Out TIR 3 and 5μm

2020-08-25T05:05:49+00:00November 14th, 2019|Categories: KNOWLEDGES|

                                         What an ER Collets using common in CNC machining   High-precision collets and precision collets. Experiment, drilling, and milling on precision instruments and equipment. The spring collets are relatively common, and the general accuracy requirement is

19 01, 2016

CNC Taper Tool Holders Standards

2020-01-15T21:44:44+00:00January 19th, 2016|Categories: KNOWLEDGES|Tags: , |

CNC TOOL HOLDERS TAPER STANDARD IN THIS WORLD At present, the main market has 7/24 and 1/10 taper shank holders, of which 7/24 has numerical control and general use, and numerical control has international standards, Germany, Japan, and the United States. A common use is a distinction between metric and inch systems. In the

19 01, 2016

CNC Retention knob & Pull Stud

2020-01-15T21:46:21+00:00January 19th, 2016|Categories: KNOWLEDGES|Tags: , |

Introduction Retention knobs to the standard of taper shank for NC tools Retention knob standard GB10945-89 "7:24 conical tool shank 40, 45 and 50 for automatic tool change machine tools The pull stud for tapered shank is made according to the international standard IS07388 / 1984. It is divided into two types: A and

19 01, 2016

The ANSI CAT Tool Holder Standard Dimension

2020-01-16T17:58:48+00:00January 19th, 2016|Categories: America Standard, CNC Standards, KNOWLEDGES|Tags: , |

CAT Tool Holder Standard Dimension US ANSI B55.50 (referred to as a) ANSI B55.50 is an American standard, the installation size is in accordance with DIN69871 IS07388 / 1 is similar, but with one wedge notch, ANSI B5.50 tool holders cannot be installed in DIN69871 and I7388

19 01, 2016

CAT SHRINK FIT TOOL HOLDER

2020-08-14T20:32:07+00:00January 19th, 2016|Categories: Alloy Steel, KNOWLEDGES|Tags: , |

The shrink fit tool holder is a hot-loading system that uses a difference between the thermal expansion coefficients of the tool holder (special stainless steel)and the tool (hard alloy) to clamp the tool strongly and with high precision. The shank material uses special stainless steel for hot-packing with a large thermal expansion coefficient, which

19 01, 2016

How to maintenance of tapered shrink fit tool holders

2020-08-26T16:36:37+00:00January 19th, 2016|Categories: KNOWLEDGES|Tags: |

How to maintenance your shrink fit tool holder   Repair and maintenance of tapered shank shrink fit tool holder Can not be re-polished, due to the difference in manufacturing processes, re-grinding of the shrinkable shank will lead to poor accuracy of the shrinkable shank. In addition, the position of the gauge line does not change much,

19 01, 2016

How to use & maintance ER clamping collets

2020-01-26T00:30:49+00:00January 19th, 2016|Categories: KNOWLEDGES|Tags: |

ER collet is a kind of collet chuck with large tightening force, wide clamping range and good precision. It is generally used for supporting the use of CNC collet tool holders. The ER clamping collet in high performance, high accuracy, simple loading and unloading and low price .

19 01, 2016

Europe Tool Holder Standard SK (DIN 69871/DIN ISO 7388-1)

2020-02-09T06:28:37+00:00January 19th, 2016|Categories: Europe Standard, KNOWLEDGES|Tags: |

Tool Holder Standard  SK (DIN 69871/DIN ISO 7388-1) Germany Shank specifications: The shank has 30, 35, 40, 45, 50, and 60 specifications, which indicates the diameter of the taper shank somewhere (the specific location is different in different standards). The specifications of the cone are usually selected

Load More Posts
Go to Top